A new technique called the Dual Parasitic Beam (DPB) technique is proposed to suppress grating lobes in a rectangular waveguide broad wall transverse slot array. This technique involves an extra layer of parasitic strip dipoles that generate the DPB to suppress the grating lobes without opposing the main beam of the original slot linear array. A full wave EM analysis in Method of Moments (MoM) is conducted to compute the coupling excitation coefficients as well as the far field patterns of the slot and dipole currents. Analysis shows that a suitable dimension and arrangement of dipoles are needed to get a desired level of dipole excitations to meet the grating suppression condition. It is found that the grating lobes can be suppressed as much as 15 dB in the presence of the parasitic dipoles. Experiments are conducted to confirm the computed results.

A novel approximate equivalent edge currents (EECs) are proposed for use in the modified edge representation (MER) for flat plates. It was reported that PO-EECs with classical PO diffraction coefficients, as applied to MER, perfectly recover PO surface integration. The inclusion of classical FW-EECs as it is, however, would not enhance the accuracy since the reality of the fringe wave is lost in the edge modification. This paper presents simple approximation for inclusion of FW-EECs in MER; FW-EECs are weighted by the function of the angle between the modified edge and the real edge. The key feature of this approach is that uniform fields are predicted everywhere though only classical diffraction coefficients are used. MER also simplifies the ray-tracing in the secondary diffraction analysis. Numerical results for diffraction from flat plates demonstrate the potential of these EECs.

A series of windows in the narrow wall of a fully-dielectric-filled rectangular waveguide to feed partially-dielectric-filled oversized-rectangular waveguide is presented. The overall structure is single-layer and 3-dimensional however; the waveguide which is uniform along the height is analyzed by the 2-dimensional method of moments and the oversized waveguide which is uniform in the longitudinal direction of the waveguide is analyzed by the 2-dimensional mode matching. It is found that utilizing simple mode conversions between the two orthogonally uniform structures is sufficient for obtaining the results similar to those of a 3-dimensional solver HFSS. The parameters for the windows designed for a uniform input division are presented. A simulation shows that a 12 window array provides a 3.5% bandwidth in terms of reflection below -20 dB. The uniform excitation of the quasi-TEM wave is confirmed in the 60 GHz band by measuring a uniform aperture field in amplitude and phase over the slotted oversized-waveguide.

Introducing diffusion bonding of laminated thin metal plates to the fabrication of slotted waveguide arrays enlightens the high potential and the feasibility of multi-layer antennas with high-performance. It is a promising process with low cost even for a double-layer antenna, because the number of etching patterns for thin metal plates is only five. In this paper, a double-layer antenna for broadband characteristics is designed in 39 GHz band as demonstration. A 20 20-element antenna is composed of 2 2 sub-arrays by installing a partially-corporate feed circuit in the bottom layer underneath radiating waveguides in the top layer. The five-element sub-arrays in both the feeding and radiating parts are designed first. A new structure for the last slot coupler with shortened termination is also proposed to avoid an extra slot-free region when assembling the neighbor sub-arrays. As the simulation results by HFSS, the maximum gain of 34.55 dBi with the antenna efficiency of 85.5% is estimated at 38.5 GHz. The test antenna is fabricated by the diffusion bonding of thin copper plates. As the measurement results, a very high aperture efficiency of 83.2% with the directivity of 34.5 dBi is realized at the center frequency of 38.75 GHz, where the antenna gain of 34.4 dBi with the high antenna efficiency of 81.4% is achieved. The bandwidth of 5.0% defined as 1 dB down from the maximum gain is achieved.

The authors have proposed a 1 m2 single-layer slotted waveguide array consisting of conducting baffles and quartz glass strips positioned in front of the slot aperture, which is referred to as a vacuum window, for microwave plasma excitation. The effect of the complicated outer vacuum window hinders the realization of uniform distribution. In this paper, a unit-cell of the alternating-phase fed single-layer slotted waveguide array with the vacuum window is analyzed by generalized scattering matrix method (GSM)-method of moments (MoM) hybridization analysis, and the array is designed to realize uniform aperture electromagnetic field distribution, where the plasma and the chamber is neglected. The GSM-MoM analysis gives reliable numerical results while the MoM has numerical errors due to singularities of Green's function for a long cavity. Uniform aperture EM field distribution outside of the vacuum window is observed in near field measurements using a 1/5 scale model antenna, and the validity of the analysis and design is verified.

A rectangular-to-radial waveguide transformer through a crossed slot is proposed as a feeder of a radial line slot antenna (RLSA) for use in a system of solar power satellite (SPS). The transformer is analyzed and designed by using the MoM with numerical eigenmode basis functions. The measured ripple of the amplitude is 3.0 dB in the φ-direction and a 7.0% frequency bandwidth for rotating mode with the ripple below 6 dB is obtained. This bandwidth is wider than that of conventional ring slot or cavity resonator with a coaxial feeder. The antenna measurements at 5.8 GHz show reasonable rotational symmetry both in the near-field distribution and the far field radiation patterns. The reflection is -27.7 dB at the design frequency and below -15 dB in the 7.0% bandwidth. The gain of the antenna with the diameter of 300 mm is 22.7 dBi and the efficiency is 56%.

The characteristics of circular polarization from a slot with a parasitic dipole are investigated analytically. It is derived that its phase is linearly dependent upon the angle of the dipole and is independent of that of slot. This interesting behavior is also confirmed by experiments.

In this paper, a three-way divider is proposed for a partially-corporate feed in an alternating phase-fed single-layer slotted waveguide array. The divider is placed at the middle of the feed waveguide and reduces the long line effects; the frequency bandwidth is doubled. It is a kind of cross junction with one input port and three output ports; most of the power is equally divided into the right and left halves of the feed waveguide while the rest of power goes straight into the center radiating waveguide. Based upon the moment method design of the three-way divider, an inductive post is introduced for wide band power dividing control to the radiating waveguide. Reflection is below -20 dB over a wide bandwidth of 24.3-26.3 GHz, and the range of power dividing ratio ranges from 1/43 to 1/4. The amplitude and the phase from the two output ports to the feed waveguide are well balanced, and the differences are less than 0.1 dB and 5.0 degrees, respectively. The MoM analysis and the wide band design are verified experimentally in the 4 GHz band.

This paper presents the formulation for the evaluation of external coupling in the alternating-phase feed single-layer slotted waveguide array antenna with baffles by using the Spectrum of Two-Dimensional Solutions (S2DS) method. A one-dimensional slot array is extracted from the array by assuming the periodicity in transversal direction and introducing the perfect electric conductors in the external region. The uniform excitation over the finite array is synthesized iteratively to demonstrate the fast and accurate results by S2DS. A unit design model with the baffles is introduced to determine the initial parameters of the slot pair which accelerate the iteration. Experiment at 25.3 GHz demonstrates good uniformity of the aperture field distribution as well as the effects of the baffles. The directivity is 32.7 dB which corresponds to the aperture efficiency 90.5% and the reflection is below -15.0 dB over 1.3 GHz.

Post-wall waveguide slot arrays are potential candidates for millimeter-wave systems. The modeling of the post-walls by the equivalent solid-walls in terms of guided wavelength is indispensable for intensive optimization of slot design for reducing computational load. In the single mode waveguide slot arrays, the modeling errors of the post-wall waveguide by the solid-wall waveguide are serious especially for the transversely located slots. The S-parameter prediction errors become larger as we increase the height of the waveguide to utilize the low-loss advantage of the waveguide. The authors propose a novel post-wall waveguide structure, named as a connected post-wall (C-PW), to enhance the equivalence. The C-PW waveguide keeps enhanced equivalence to the solid-walls even for a larger substrate height. The predictions are confirmed by simulations and measurements. An 8-element linear array of reflection-cancelling slot pairs is designed by using the equivalent solid-wall model to demonstrate the feasibility of the simple design in the C-PW.

A radial line slot antenna (RLSA) is a slotted waveguide planar array for the direct broadcast from satellite (DBS) subscriber antennas. A single-layered RLSA (SL-RLSA) is excited by a radially outward traveling wave. The antenna efficiency of more than 85% has already been realized. These antennas are designed on the assumption of perfectly rotationally symmetrical traveling wave excitation; the slot design is based upon the analysis of a slot pair on the rectangular waveguide model with periodic boundary walls. However, the slots perturb the inner field and the actual antenna operation is not perfectly symmetrical. This causes the efficiency reduction especially for very small size antenna. This paper presents a fundamental analysis of the inner field of the radial waveguide. It is impossible to analyze all the slot pairs in the aperture as it is and only the slots in the inner few turns are considered since these provide dominant perturbation. The calculated results are verified by the experiments and reasonable agreement is demonstrated. Some design policies are suggested for enhancing the rotational symmetry.

A post-wall waveguide slot array with a three-way power divider on a single-layer substrate is designed to have a H-plane sectoral beam and an E-plane cosecant pattern with null-filling. Experiments in the 26 GHz band confirmed the sectoral beam with a -3 dB beam width of 117 deg and a ripple width of 2 dB in the sector.

Recently most of the singularities of the equivalent edge currents for flat plates were eliminated by the authors using the paths of most rapid phase variation. A unique direction on the plate was determined for given incidence and observer. This paper extends this method for arbitrary angle wedges and presents the new expressions of the equivalent edge currents. The resultant expressions are valid for any incidence and observation aspects and have no false singularities. Diffraction patterns and radar cross sections of 3-D objects composed of wedges are calculated by using these currents. They show good agreements with experimental data or the results by the other methods.

In the millimeter-wave band, the series-fed array antenna is facing a problem of large transmission loss and narrow bandwidth by using a high-permittivity and large-loss-tangent material. In this paper, an air region is inserted in the half of the height in the LTCC waveguide of εr =6.6 and tanδ =0.013 to reduce the transmission loss. The reduction of the equivalent dielectric constant by the air insertion structure enhances both the gain and the bandwidth of the series-fed slot array. The transmission loss of the single-mode rectangular waveguide has been reduced to about 1/6 by using the partially-filled structure in the 60-GHz band. In a one-dimensional slot array, the total loss has also been reduced to about 1/7. And the 3 dB-down gain bandwidth has also been increased from 1.3 GHz to 2.3 GHz.

The effects of finite ground plane upon the patterns of the GPS patch antennas are analyzed by EEC with modified edge representation (MER). The comparison with UTD and measurements shows that low elevation patterns including axial ratios are successfully predicted.

A spiral array radial line slot antenna (SA-RLSA) is designed in 22 GHz band. A SA-RLSA excited with a coaxial feeder suffers from aperture illumination fluctuation in amplitude and phase in the circumferential (φ-) direction while in the radial direction, reasonably uniform distribution is observed. Rotational symmetry of radiation patterns is degraded and especially the sidelobe levels are unbalanced. This fluctuation is associated with the generation of the higher order modes in the φ-direction and is the unique defect of SA-RLSA which uses oversized waveguide. In this paper, a novel feeding structure with two pairs of parasitic pins around a coaxial feeder is proposed and designed so as to compensate the rotational asymmetry of aperture illumination. A measurement using the model antenna designed in 22 GHz band demonstrates the enhancement of the rotational symmetry; the circumferential fluctuation is reduced from 5.1 dB and 33 degrees to 1.8 dB and 12 degrees, while the fluctuation in the first sidelobe level suppressed from 10.7 dB to 1.2 dB.

Physical optics(PO) and the aperture field integration method (AFIM) give accurate and similar field patterns near the first few sidelobes of reflector antennas. It is widely accepted that the use of AFIM is restricted to norrower angles than PO. In this paper, uniform equivalent edge currents of PO and AFIM are compared analytically and their equivalence in high frequency in discussed. It is asymptotically verified that the patterns by AFIM are almost identical to PO fields in the full 360angular region, provided that AFIM uses the equivalent surface currents consisting of two components, that is, the geometrical optics(GO) reflected fields from the reflector and the incident fields from the feed source, the latter of which are often neglected. Slightly weaker equivalence is predicted for cross polarization patterns. Numerical comparison of PO and AFIM confirms all these results, the equivalence holds not only for large but also for a very small refiector of the order of one wavelength diameter.

Rectangular/circular-to-radial waveguide tra-nsformers through a ring slot have been proposed for the feeder of radial line slot antennas (RLSAs) in millimeter wave application. Rotating electric modes are excited by a set of ring slot and perturbation dog bone slot. Basic operation is observed in 12 GHz band. Concentric array radial line slot antennas fed by these transformers are fabricated and the antenna gain of 26.9 dBi with the efficiency more than 60% is measured. The applicability for millimeter wave is verified for 38 GHz band RLSA fed by the rectangular waveguide. The measured gain of the antenna is 22.5 dBi with the efficiency of 53% with the diameter of 46mm and 26.4 dBi with 61% with the diameter of 66mm.

The method of equivalent edge currents (MEC) has some ambiguity about definition of edge currents at general edge points except for diffraction points. The modified edge representation is introduced to overcome this ambiguity. The modified edge is the fictitious one which is defined so as to satisfy the diffraction law for given directions of incidence and observation. The equivalent edge currents for physical optics (PO) components at general edge points are obtained by utilizing these fictitious edges and the classical Keller's diffraction coefficients. High potentials of these currents are numerically demonstrated for diffraction from a disk, a square plate and a parabolic reflector.

The authors design a simple feed system for a planar slotted waveguide array. A waveguide π-junction with negligible reflection is cascaded to compose a multiple-way power divider. The frequency characteristics of the power divided to each port and the reflection at the feed point are discussed and high performances are predicted. The maximum number of cascaded junctions in this system can be determined in terms of a desired frequency bandwidth and allowable deviation in divided power.